Nozzles, Fire Hose, Brass & Sprinkler Products

nozzles0

POLYCARBONATE FIRE HOSE NOZZLES

nozzles1
nozzles3
ULC

MANUFACTURED In Canada

HIGH IMPACT POLYCARBONATE NOZZLES

  • 1½” Adjustable Fog/Stream/Shut-off.
  • ULC Listed for Class A & B Fires Only.
  • Max rated flow 78 gpm at 100 PSI. Molded in Red.

NOT TO BE USED FOR WASHDOWN

PART # DESCRIPTION
15 1½” Adjustable Fog/Stream/Shut-off.
ULC Listed for Class A & B Fires Only.
CR15 1½” Adjustable Fog/Stream/Shut-off.
NG15 Nozzle Gasket

ULC Listed for Class A & B Fires Only

CHROME FIRE HOSE NOZZLES

nozzles2
15E – 1½ Adjustable Fog/Shut-off only. ULC Listed for Class A, B & C (electrical) fires. Max rated flow 78 gpm at 100 PSI.  Molded in Red.

PART # DESCRIPTION
15E 1½” Adjustable Fog/Shut-off only.
ULC Listed for Class A, B & C
(Electrical) Fires
nozzles3

10  – 1 Adjustable Fog/Stream/Shut-off. Molded in Red.

PART # DESCRIPTION
10 1” Adjustable Fog/Stream/Shut-off.
For Class A, B Fires Only.
NG10 Nozzle Gasket

BRASS FOG NOZZLES

brass fog fire nozzles
These brass fog nozzles that are precision machined with a stain brass finish.  U.L. Listed and FM approved for non electrical fires, Class A & B Fires Only.

PART # DESCRIPTION
1575B 1½” Adjustable Brass Fog/Stream/Shut-off.
ULC Listed for Class A & B Fires Only.

FIRE HOSE

RACK AND REEL FIRE HOSE

rack and reel fire hose

Rack and reel fire hose is fully lined and FM Labeled. It has an acceptance test pressure of 500 PSI and a service test of 250 PSI. Each section comes already folded for ease of installation on pin racks. NOTE: This inexpensive lightweight hose is designed for use as emergency fire hose only! It should never be used for wash down or any other purpose. U.L.C. Labeled rack and reel fire hose is available for an additional fee.

PART # DESCRIPTION BOWL
SIZE
WEIGHT
COUPLED
RH50 50’ x 1½” Brass 1¹¹⁄₁₆” 7 lbs.
RH75 75’ x 1½” Brass 1¹¹⁄₁₆” 9 lbs.
RH100 100’ x 1½” Brass 1¹¹⁄₁₆” 12 lbs.

SINGLE JACKET FIRE HOSE

single jacket fire hose
The single jacket fire hose has a burst pressure of 750 PSI, an acceptance test pressure of 500 PSI, a service test of 250 PSI and is FM Labeled.  Made of 100% polyester, rubber lined material for strength and flexibility.  Recommended for industrial fire protection. U.L.C. Labeled available at extra cost.

PART # DESCRIPTION BOWL
SIZE
WEIGHT
COUPLED
*SPECIAL ORDER
SJ5051 50’ x 1½” Alum. 1¾” 13 lbs.
SJ7551 75’ x 1½” Alum. 1¾” 18 lbs.
SJ10051 100’ x 1½” Alum. 1¾” 25 lbs.
*SJ5052 50’ x 2½” Alum. 2¹³⁄₁ 25 lbs.
*SJ10052 100’ x 2½” Alum. 2¹³⁄₁₆” 51 lbs.

*Must specify Thread Type on 2½” hose AMA-BC-CSA-QST-NFLD-NS-WCT

DOUBLE JACKET FIRE HOSE

double jacket fire hose
The double jacket fire hose has a burst pressure of 1200 PSI, an acceptance test pressure of 800 PSI, a service test of 400 PSI and meets NFPA 1962.  Made of 100% polyester, rubber lined material for strength and flexibility.  Recommended for industrial fire protection.

PART # DESCRIPTION BOWL
SIZE
WEIGHT
COUPLED
*SPECIAL ORDER
DJ5081 50’ x 1½” Alum. 1¹⁵⁄₁₆” 18 lbs.
DJ10081 100’ x 1½” Alum. 1¹⁵⁄₁₆” 32 lbs.
*DJ5082 50’ x 2½” Alum. 3” 34 lbs.

*Must specify Thread Type on 2½” hose AMA-BC-CSA-QST-NFLD-NS-WCT

yellow polymer impregnated fire hose

YELLOW POLYMER IMPREGNATED FIRE HOSE

The yellow polymer impregnated fire hose has the same specifications as our standard double jacket hose except that the outside jacket is independently and completely impregnated with abrasion resistant, water repellent polymer. Available in aluminum couplings only.

PART # DESCRIPTION BOWL
SIZE
WEIGHT
COUPLED
*SPECIAL ORDER
DJ5081Y 50’ x 1½” Alum. 1¹⁵⁄₁₆” 21 lbs.
*DJ5082Y 50’ x 2½” Alum. 3” 39 lbs.

*Must specify Thread Type on 2½” hose AMA-BC-CSA-QST-NFLD-NS-WCT

WASHDOWN HOSE

washdown hose
WASHDOWN HOSE Very Heavy Duty Industrial and Maintenance. Features a unique double jacket cover designed for extremely abrasive conditions in municipal street wash and con- struction environments. Resistant to chemicals, oils, fuels, ozone, UV, rot and mildew. Two hoses in one.

  • Inner Hose – 100% Synthetic Polyester Filament
  • Outer Hose – Polyurethane. Remains flexible to -55°C (-67°F). Available in 1½” (38 mm) only.
PART # DESCRIPTION BOWL SIZE
WASH 50 50’ x 1½” 1¹¹⁄₁₆”
WASH 75 75’ x 1½” 1¹¹⁄₁₆”
WASH 100 100’ x 1½” 1¹¹⁄₁₆”

RINGS & GASKETS

FIRE HOSE COUPLINGS, RINGS & GASKETS RACK AND REEL COUPLINGS.

ring1

PART # DESCRIPTION
BPRC15 1½” Brass RH NPSH Coupling
TG15 1¹¹⁄₁₆” Bowl Tail Gasket for RH
SHG15 1½” Swivel Hose Gasket for RH
ER15 1½” x ⅞” RH Expansion Ring

SINGLE JACKET COUPLINGS, RINGS AND GASKETS.

ring2
PART # DESCRIPTION
BSJC15 1½” Brass SJ NPSH Coupling
ASJC15 1½” Aluminum SJ NPSH Coupling
*BSJC25 2½” Brass SJ Coupling
*ASJC25 2½” Aluminum SJ Coupling
TG15 1¹¹⁄₁₆” Bowl SJ Tail Gasket
TG25 2¹³⁄₁₆” Bowl SJ Tail Gasket
SHG15 1½” Swivel Hose Gasket
SHG25 2½” Swivel Hose Gasket
ERS1 1½” x 1¼” SJ Expansion Ring
ER25 2½” x 1¼” SJ Expansion Ring

DOUBLE JACKET COUPLINGS, RINGS AND GASKETS.

ring3
PART # DESCRIPTION
BDJC15 1½” x 1¹⁵⁄₁₆” Brass DJ NPSH Coupling
ADJC15 1½” x 1¹⁵⁄₁₆” Aluminum DJ NPSH Coupling
*BDJC25 2½” x 3” Brass DJ Coupling
*ADJC25 2½” x 3” Aluminum DJ Coupling
DJTG15 1¹⁵⁄₁₆” Bowl DJ Tail Gasket
TG25 2¹³⁄₁₆” Bowl DJ Tail Gasket
ERD1 1½” x 1¹⁄₁₆” DJ Expansion Ring
ER251 2½” x 1½” DJ Hose Expansion Ring
SHG15 1½” Swivel Hose Gasket
SHG25 2½” Swivel Hose Gasket

*MUST SPECIFY THREAD TYPE: AMA, BC, CSA, QST, NFLD, NS, WCT

HANGER

TARATON HOSE HANGER

Taraton hose hanger constructed of aluminum alloy casting to accommodate lined or unlined hose up to 2½”. The top shoulder is spring loaded so that one pull or water pressure is sufficient to release the hose. Low cost, stored close to walls or columns to minimize damage and fewer bends in the hose to prolong its life.

PART # RACK
HOSE
SJ
HOSE
DJ
HOSE
HOSE
DIA.
L H
THH TOP 100’ 100’ 100’ 1 – 2½” 6½” 7”
THH BOTTOM 100’ 100’ 100’ 1 – 2½” 4½” 4¾”
PART # DESCRIPTION
THH Taraton Hose Hanger for 100’ of Hose

PACK ACCESSORIES

taraton_hose_hanger1
PART # DESCRIPTION
FOGC Fog Nozzle Clip for Pin Rack
RPIN Pin Rack
FHWB Wall Bracket for Pin Rack
RN 1½” Rack Nipple c/w Nut (Steel)

REELS & RACKS

HEAVY DUTY HOSE REELS

reels_racks1

Heavy duty hose reels shipped assembled. Red baked enamel finish. Comes with a 14 gauge steel wall bracket that swings 180°.

PART # RACK HOSE SJ HOSE DJ HOSE HOSE DIA. L H W
HDR18 100’ 75’ 1½” 23½” 18” 6¼”
HDR24 150’ 100’ 1½” 29” 24” 6¼”
Part # Description
HDR18 18” Hose Reel
HDR24 24” Hose Reel

RUGGED HEAVY DUTY HOSE REELS

reels_racks2

Rugged heavy duty hose reels have sides and hub constructed of 16-gauge steel. Welded steel 1″ x ³⁄₁₆” reel bracket, with a 1½” x ¼” wall bracket, provides superior support. Wall bracket swings 180°. Comes with reusable hook and loop back strap to prevent accidental unrolling of hose.

PART # HOSE DIA. RACK HOSE SJ HOSE DJ HOSE L H W
HDR25HC 1½” 300’ 200’ 150’ 29” 24” 8¾”
HDR25HC 2½” 150’ 100’ 75’ 29” 24” 8¾”
Part # Description
HDR25HC 25” High Capacity Heavy Duty Hose Reel

HOSE TRAY

hose tray

Hose tray is designed to take up to 100’ of 1½” rack hose or 50’ of 1½” industrial hose. Well constructed of heavy duty steel. Ideal for use in an area where hose may need extra protection.

Part # Description
HT Hose Tray 23” x 15” x 4”

PIN TRAY

vinyl fire hose reel cover

Red enameled steel PIN RACKS with moveable pins. The auto – matic release mechanism keeps water from flowing into the hose while the water supply valve is opened, until the last fold is removed. This unit is U.L. Listed and FM Approved.

PART # DESCRIPTION
HR-100 Hose Rack c/w Fog Nozzle Clip (red) ULC for
100’ Hose (23 pins)
HR-75 Hose Rack c/w Fog Nozzle Clip (red) ULC for
75’ Hose

AVAILABLE CHROME PLATED CALL FOR PRICING

VINYL COVERS FOR RACKS & REELS HOSE REEL COVERS

reels_racks5

Available in English & French. Fluorescent Red.

Part # Description
E-HRC-18 For 18” diameter Reel, Hose Reel Cover
E-HRC-24 For 24 diameter Reel, Hose Reel Cover
E-HRC-25 For Heavy Duty Reel, Hose Reel Cover

ANGLE VALVES

angle_valves1

SINGLE HOSE VALVE made of cast brass for use with pin rack assembly. Tested to 300 PSI.

Part # Description
FM150 1½” Female to Male Angle Valve c/w Hydrolator – ULC
FF150 1½” Double Female Angle Valve c/w Hydrolator – ULC

CHROME VALVES AVAILABLE AT EXTRA COST (SPECIAL ORDER)

BRASS REDUCERS.

brass_reducers1

Brass reducers Female x Male pin lug adapter (used to change size and/or threads)

PART # DESCRIPTION
250-150 2½” F x 1½” M REDUCER
(CSA, QST, WCT, BC, AMA)
250-1501 2½” THREAD REDUCER (NS & NFLD)

CHROME AVAILABLE ON REQUEST

BRASS CAPS

brass_caps1

Brass caps used with fire department connections, hydrants, valves, etc. to hold back water.

PART # DESCRIPTION
2500-B 2½” Threaded Cap c/w Chain
(CSA, QST, WCT, BC, AMA)
2500-B1 2½” Threaded Cap (NS & NFLD)
1500-B 1½” Threaded Cap c/w Chain (NPSH THREAD)

BRASS PLUGS

brass_plugs

Brass plugs used with fire department inlet connections, siamese, single inlet, etc. to keep inlet ports free of debris.

PART # DESCRIPTION
2500-BP 2½” Threaded Plug c/w Chain
(CSA, QST, WCT, BC, AMA)
2500-BP1 2½” Threaded Plug (NS & NFLD)
CHROME AVAILABLE ON REQUEST

HANDWHEEL REPLACEMENT PART FOR VALVE HOSES

PART # DESCRIPTION
HWV-7 Handwheel for 7/16” Angle Valve Stem

PLASTIC BREAK CAPS

Not threaded, easily broken with a hydrant/spanner wrench.

PART # DESCRIPTION
PAC Adjust-A-Plug Plastic Break Cap
PBC 2½” Molded Plastic Break Cap
c/w J Hooks
U250 2½” Push On Cap c/w Chain
U250 2½” Threaded Cap c/w Chain (CSA, Thread)
B250C 2½” Threaded Cap c/w Chain CHROME
(CSA, Thread)
B150 1½” Threaded Cap c/w Chain (NPSH Thread)
plastic_break_caps3
plastic_break_caps1
plastic_break_caps2

WRENCHES & AXES

Spanner wrench

PART # DESCRIPTION
150W Universal Spanner Wrench – 1½” Rocker
or Pinlugs
250W Universal Spanner Wrench – 1½” to 3”
250H Combination Spanner Wrench c/w Hydrant
Key 1½” to 3”

Universal SPANNER WRENCH made of cast aluminum that fits hose lugs 1½“ thru 3“

PART # DESCRIPTION
250K Universal Spanner Wrench complete with
Gas Key Shut-Off

Heavy duty adjustable combination HYDRANT/SPANNER WRENCHES made of steel/ductile iron.

PART # DESCRIPTION
W575 Adjustable Combination Hydrant and
Spanner Wrench

Standard adjustable combination HYDRANT/SPANNER WRENCHES made of steel/ductile iron.

PART # DESCRIPTION
W580 Adjustable Combination Hydrant and
Spanner Wrench

PICK HEAD FIRE AXE with a 6 lb. head and 36” hickory handle. Precision balanced for safe handling. Optional mounting bracket and hook available separately.

PART # DESCRIPTION
406M 6 lb. Pick Head Fire Axe
AB408 Axe Bracket and Hook
plastic_break_caps4_1
plastic_break_caps4_2

SPRINKLERS

SPRINKLER HEADS – 1/2″

sprinkler_heads1

BRASS U.L.C. Listed and FM Approved Sprinkler Heads.

PART # DESCRIPTION
J155P 155° Pendant Bulb Brass
J155U 155° Upright Bulb Brass
J200P 200° Pendant Bulb Brass
J200U 200° Upright Bulb Brass
J286P 286° Pendant Bulb Brass
J286U 286° Upright Bulb Brass

3/4” Available Upon Request

CHROME SPRINKLER HEADS

sprinkler_heads2

Chrome U.L.C. Listed and FM Approved Sprinkler Heads – 1/2″.

PART # DESCRIPTION
J155PC 155° Pendant Bulb Chrome
J155UC 155° Upright Bulb Chrome
J200PC 200° Pendant Bulb Chrome
J200UC 200° Upright Bulb Chrome
J286PC 286° Pendant Bulb Chrome

3/4” Available Upon Request

SPRINKLER WRENCHES

sprinkler_heads3
PART # DESCRIPTION
RSWD Recessed Sprinkler Wrench
SPWR Sprinkler Wrench

SPRINKLER ESCUTCHEONS

sprinkler_heads4
PART # DESCRIPTION
EPC One Piece Escutcheon Plate for
Sprinkler Heads – Chrome
EPA 2 Piece Escutcheon Plate for
Sprinkler Heads – Chrome
EP650 Split Chrome Escutcheon Cup

SPRINKLER CAGE

sprinkler_heads5

SPRINKLER CAGE made of red painted steel.

PART # DESCRIPTION
SPG Economy Sprinkler Guard

SPRINKLER CABINET

SPRINKLER CABINET made of red painted steel that can be wall mounted. Will hold up to 6 sprinkler heads and a wrench.

PART # DESCRIPTION
SHC1 Emergency Sprinkler Cabinet  ONLY

SPRINKLER SIGNS

Sprinkler identification signs made of aluminum, painted white, then printed with fade resistant red ink. Each sign has predrilled mounting holes for easy installation.

PART # DESCRIPTION
A221 Air Control *
A222 Air Line *
A223 Alarm Line *
A163 Alarm Test
STAG Complete Single Riser Set
sprinkler_signs1
PART # DESCRIPTION L X H
A224 Anti-Freeze System * 6″ x 2″
A225 Auxiliary Drain * 6″ x 2″
sprinkler_signs2
PART # DESCRIPTION L X H EACH
A142 This Valve Controls 6″ x 4″ 15.00
A226 This Valve Controls * 9″ x 7″ 25.00
sprinkler_signs3
PART # DESCRIPTION L X H
A143 Control Valve 6″ x 2″
A227 Drain * 6″ x 2″
A228 Drain Valve * 6″ x 2″
A229 Dry Standpipe * 6″ x 2″
sprinkler_signs4
PART # DESCRIPTION L X H
A160 Inspection Test 6″ x 2″
A230 Entire System * 6″ x 2″
A231 Fire Sprinkler Valve * 6″ x 2″
sprinkler_signs5
PART # DESCRIPTION L X H
A164 Hydraulic Data 6″ x 4″
A232 Hydraulic System * 5″ x 7″
sprinkler_signs6

* Sign has plastic coating to prevent scratching.

sprinkler_signs7
PART # DESCRIPTION L X H
A233 Main Control * 6″ x 2″
A161 Main Drain * 6″ x 2″
A234 Normally Closed * 6″ x 2″
A235 Normally Open * 6″ x 2″
sprinkler_signs8
PART # DESCRIPTION L X H
A236 Open Sprinkler Control * 6″ x 2″
A237 Open Sprinkler Drain * 6″ x 2″
A162 Sprinkler Drain * 6″ x 2″
sprinkler_signs9sprinkler_signs10
PART # DESCRIPTION L X H
A165 Sprinkler Fire Alarm 7¾” x 6″
A238 Sprinkler Valve Room * 6″ x 2″
A239 Test & Drain * 6″ x 2″
A240 Test Valve * 6″ x 2″
A241 Water Motor Line * 6″ x 2″
A242 Wet Standpipe * 6″ x 2″
PART # DESCRIPTION DIAMETER
RP251 911 Fire Alarm Bell, Plastic * 7″ dia.

FIRE SPRINKLER LINE LABEL

Fire sprinkler line label with arrow. Fade resistant red ink, printed on white self adhesive vinyl. Use to identify sprinkler lines and the direction of flow. Rolls of 100 labels

sprinkler_signs11
PART # DESCRIPTION L X H
BL252 Fire Sprinkler Line with Arrow 6″ x 2″

* Signs have plastic coating to prevent scratching.

Sprinkler Gauges

sprinkler_signs12

Sprinkler gauges are designed for use on wet or dry sprinkler systems. The 3½” gauges are UL listed and FM approved. The SG1 is used in a dry system on the sprinkler head side of the control valve to accurately monitor line air pressure, with the ability to accept water pressure up to 250 psi (upon system acti- vation). The SG2 is used on the water supply side of the system to indicate available source pressure. The SG3 accommodates both air and water sides, up to 300 psi. Custom gauge faces are available with your name and phone number. Call the Sales Department for more information.

PART # DESCRIPTION
SG1 Air/Water Retard Gauge, 0-80/250 psi
SG2 Water Gauge, 0 – 300 psi
SG3 Air/Water Gauge, 0 – 300 psi